Analisa sifat mekanik material logam melalui pemodelan dan simulasi uji tarik berdasarkan metode elemen hingga

A. Susanto; M.T. Mahendra; R.P. Andriyani

doi:10.29303/dtm.v14i1.824

Analisa sifat mekanik material logam melalui pemodelan dan simulasi uji tarik berdasarkan metode elemen hingga

A. Susanto, M.T. Mahendra, R.P. Andriyani

Abstract

Mechanical properties of material are attributes that should be known by engineers and product designers to determine the suitability of the structure being designed. One of the ways to determine the mechanical properties of a material is generally conducted by well-known tensile test. By the test, it will inform the elastic, plastic and fracture areas are known in the strain-stress diagram. Apart from that, the yield strength and maximum tensile strength can also be observed. The obstacle factor in experimentally tensile testing is the expensive costs, both for renting and procuring a tensile testing machine, which is called universal testing machine (UTM). This research aims to provide an alternative tensile test method, namely modeling and simulation techniques based on the finite element method (FEM). The workpiece material applied was ST37 Steel. This material is widely utilized in various types of industry, including the automotive, railway, and construction industries. The results show that the simulation can display all events that tensile tests may not be able to display experimentally, such as information on stress distribution and also elongation during the test. In addition, the mechanical properties of the ST37 material were obtained, including the yield strength of the material (yield point, Y) and the maximum tensile strength (ultimate tensile strength, σ_max) which were 812.3 and 928.1 MPa, respectively.

Keywords

Tensile test simulation, finite element method, mechanical properties, ST37 steel

Full Text:

PDF

References

ASTM E8, ASTM E8/E8M standard test methods for tension testing of metallic materials 1, Penerbit Annual Book of ASTM Standards 4 (Issue C, pp. 1–27), 2010.

Kalpakjian, S., Schmid, S.R., Manufacturing engineering and technology, Penerbit Prentice Hall International, Singapore, 2001.

Li, H., Chen, Y., Handbook of manufacturing engineering and technology, Penerbit Springer Verlag, London. 2014.

Mudmainah, P.H.W., Susanto, A., Ciptaningrum, A., Alfiyani, R., dan Wicaksono, R.E., Variasi kedalaman potong terhadap gaya potong dan temperatur pada proses bubut baja AISI 304, Jurnal Rekayasa Material, Manufaktur dan Energi, 6(1), 106–118, 2023.

Nofita, F., Susanto, A., Yuliar, W., Adya, J., dan Adhi, M., Pengaruh variasi kecepatan pemakanan (feed rate) terhadap gaya potong proses gurdi dengan material aluminium, Rotasi, 25(1), 40–46, 2023.

Rosdi, F.N.M., Salim, N., Roslan, R., Bakar, N.H.A., Sarmin, S.N., Potential red algae fibre waste as a raw material for biocomposite, Journal of Advanced Research in Applied Sciences and Engineering Technology, 30(1), 2023.

Sathiamurthi, P., Karthi Vinith, K.S., Sathishkumar, T.P., Arunkumar, S., Anaamalaai, A.S., Fiber extraction and mechanical properties of Agave Americana/Kenaf fiber reinforced hybrid epoxy composite, Materials Today: Proceedings, 46, 8594–8601, 2021.

Schey, J.A., Proses manufaktur: introduction to manufacturing processes, edisi ketiga, Penerbit Andi, Yogyakarta, 2009.

Susanto, A., Pendekatan alternatif dalam menghasilkan stability lobes diagram untuk memprediksi getaran chatter pada proses pemesinan berdinding tipis, SPECTA: Journal of Technology, 5(1), 48–57, 2021.

Susanto, A., Arrosida, H., Fajar, M., Choirul, A., dan Azka, M., Hubungan parameter pemesinan terhadap gaya potong, temperatur, dan power pada proses bubut Inconel 718, Rotasi, 24(3), 43–49, 2022.

Wahyudi, N., Faizin, K.N., Susanto, A., Sari, S.F., Mahmud, R., Mechanical characteristics of bio-composite materials reinforced by Pandanus Tectorius natural fibers, International Journal of Innovative Science and Research Technology, 8(12), 351–359, 2023.

DOI: https://doi.org/10.29303/dtm.v14i1.824