Pengaruh waktu tahan pack carburizing dan penggunaan media quenching cane molasses terhadap sifat mekanik dan struktur mikro baja karbon rendah

S. Darmo, E. D. Sulistyowati, R. M. Wahyu

Abstract


 

Pack carburizing is one of the methods used to increase the carbon content in steel by using solid media. In this study, the addition of carbon elements was carried out using teak wood charcoal and cow bone powder, after that in quenching using cane molasses. Variations used for holding time are 2 hours, 4 hours, and 6 hours, variations in cane molasses content used 10%, 20%, 30%, and the percentage comparison between cow bone powder and teak wood charcoal is 50%:50%. The results of this study show that the pack carburizing resistance time factor is more influential on the mechanical properties and microstructure of low carbon steel. The highest hardness value is found at a holding time of 6 hours with quenching cane molasses 20% of 799.95 kg/cm2 and the lowest hardness value is found without treatment of 162.62 kg/cm2. For the highest impact toughness is found without treatment of 2.02 Joule/mm2 and the lowest impact toughness value is found at holding time of 6 hours with quenching cane molasses 20% of 1.127 Joule/mm2. For microstructures formed after treatment, martensite structures are formed due to rapid cooling.


Keywords


Pack carburizing; quenching; holding time; cane molasses

Full Text:

PDF

References


Abidah, A.F., Drastiawati, N.S., Analisis SS400 hasil carburizing media arang tempurung kelapa-BaCO3 dengan variasi temperatur pemanasan dan holding time ditinjau dari pengujian kekerasan dan struktur mikro, Jurnal Teknik Mesin, 7(2), 1-8, 2019.

Bahtiar, Iqbal, M., Arisandi, D., Analisis kekerasan dan struktur mikro pada baja komersil yang mendapatkan proses pack carburizing dengan arang cangkang kelapa sawit, Jurnal Teknik Mesin, 8(1), 686-696, 2017.

Dodo, M.R., Ause, T., Adamu, M.A., Investigating the cooling rate of cane molasses as quenching medium for 0.61% c high carbon steels, Association of Metallurgical Engineers of Serbia, University Zaria Nigeria, 22(1), 39-49, 2016.

Mazuli, S., Haripriadi, B.D, Analisis pengaruh arang kayu bakau arang tempurung kelapa dan arang kayu leban pada proses pack carburizing terhadap kekerasan baja karbon ST-37, Jurnal Rekayasa Material Manufaktur dan Energy, 3(2), 128-137, 2020.

Masyrukan, Penelitian sifat fisis dan mekanis baja karbon rendah akibat pengaruh proses pengarbonan dari arang kayu jati, Media Mesin, 7(1), 40-46, 2006.

Nanulaitta, N.J.M., Lilipaly, E.R.M.A.P., Analisis perbandingan komposisi karbon dan bubuk tulang sapi dalam proses karburasi padat untuk mendapatkan nilai kekerasan tertinggi pada baja karbon S-35 C, Jurnal Arika, 5(2), 43-49, 2011.

Purnomo, D.J., Jokosisworo, S., Budiarto, U., Analisa pengaruh holding time tempering terhadap kekerasan keuletan ketangguhan dan struktur mikro pada baja ST 70, Jurnal Teknik Perkapalan, 7(1), 71-78, 2019.

Rahmawati, Nugroho, Y., Prihatiningtyas, E., Identifikasi kesehatan tanaman jati (Tectona grandis linn. f) di Kabupaten Banjar Kalimantas Selatan, Jurnal Sylva Scienteae, 2(5), 35-40, 2019.

Sujita, Yudhyadi, I.G.N.K., Zainuri, A., Adhi, I.G.A.K.C., Sutanto, R., Pengaruh media pendingin dan waktu pada perlakuan pack carburizing-quenching baja karbon rendah SS400, Jurnal Dinamika Teknik Mesin, 11(2), 34-40, 2021.

Yuliana, R., Rahim, E.A., Hardi, J., Sintesis hidroksiapatit dari tulang sapi dengan metode basah pada berbagai waktu pengadukan dan suhu sintering, Jurnal Kovalen, 3(3), 201-210, 2017.




DOI: https://doi.org/10.29303/dtm.v12i1.495

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Sujita Sujita Darmo, Emy Dyah Sulistyowati, Rifki Maulana Wahyu

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

 
 

After being re-accredited, the Journal of Dinamika Teknik Mesin, still has sinta 3 (S3) which is valid until 2025, but certificates and decrees have not been issued.