Email this article 
Analisa Pengaruh Variasi Merek Kampas Rem Tromol Dan Kecepatan Sepeda Motor Honda Supra X125 Terhadap Keausan Kampas Rem
Abstract
Abstract
Brake is one component of a motor vehicle that serves to slow or stop the study aims to determine the value of the wear of each brand of brake drum caused by variations in the speed of the motorcycle Honda Supra X125 on the braking load 6 kg.
Brake that is used in this study there are three variations of the brand is a brand HONDA GENUINE PART, ASPIRA, and KOMACHI with variations at 40, 50 and 60 km / h and braking load 6 kg. The research was conducted in two phases, namely the field of testing and measuring brake wear in the lab. Metrology using a profile projector, in addition to the Rockwell hardness testing is also performed to determine the hardness of each brand of brake lining before and after testing higher speeds with the same braking load time, braking distance and the wear rate also increased.
From the research results smallest brake lining wear occurs there at a speed of 40 km / h and braking load 6 kg. Genuine Parts for the Honda brand it wear amounted to 1.574 x 10 -5 mm / sec, while the brand Aspira it wear 8.47 x 10 -5 mm / sec and brands Komachi it wear 3.500 x 10 -5 mm / sec. Largest brake wear occurs at a speed of 60 km / h and braking load 6 kg. Genuine Parts for the Honda brand is equal to 2.373 x 10 -5 mm / sec, while the brand Aspira it wear 3.626 x 10 -5 mm / sec and brands Komachi it wear 3.701 x 10 -5 mm / sec.
Full Text:
PDFReferences
Budiono, Eko (2010). tentang keausan kampas rem asli dan imitasi sepeda motor honda tiger, yamaha scorpio, suzuki thunder, dan kawasaki ninja. universitas gunadarma,
Dewanto, J., Wibowo.S., (2008). Kajian Pengeruh Gerak Relatif Sepatu Gesek Terhadap Efektifitas Pengereman Pada Jenis Rem Tromol Studi Kasus Untuk Rem Sepeda Motor. Seminar Nasional Teknik Mesin 3. Diakses 16 Januari 2009 dari www.petra.ac.id.
Hardianto,Ian Siahaan., Yung,Hoo Sen,(2008). Kinerja Rem Tromol Terhadap Kinerja Rem Cakram Kendaraan Roda Dua Pada Pengujian Stasioner, Jurusan Teknik Mesin Universitas Kristen Petra, Surabaya.
Hardianto,Ian Siahaan., Yung,Hoo Sen, (2008). Kinerja Rem Tromol Terhadap Kinerja Rem Cakram Kendaraan Roda Dua Pada Pengujian Stasioner, Jurusan Teknik Mesin Universitas Kristen Petra, Surabaya.
Haroen, Kartiwa Wawan dan Waskito, Arief Tri (2008 ). Peningkatan Standar Kanvas Rem Kendaraan Berbahan Baku Asbestos dan Non Asbestos (Celulose) Untuk Keamanan.Semarang JATENG.
Jama, Jalius (2008). Teknik Sepeda Motor Jilid 3 untuk SMK Departemen Pendidikan Nasional, Jakarta.
Lubi, (2001). Perancangan Kampas Rem Beralur dalam Usaha Meningkatkan Kinerja serta Umur dari Kampas Rem, Jurusan Teknik Mesin FTI-ITS Surabaya.
Maulana, Tri, (2010). Pembuatan Dan Pengujian Sifat Fisis Dan Mekanis Kampas Rem Dengan Bahan Dasar Arang Tempurung Kelapa Dengan Matriks Epoxy, Jurusan Teknik Mesin Univesitas muhamadiyah Surakarta.surakarta
Setianto,Imam, (2009). Pengaruh Variasi Temperatur Sintering Terhadap Ketahanan Aus Bahan Rem Sepatu Gesek,universitas muhamadiyah Surakarta, Surakarta.
Welianto,Andre (2010). Pengaruh Keausan Brake Pad Terhadap Waktu Pengereman Pada Pengujian Stationer, Jurusan Teknik Mesin Univesitas Kristen Petra,surabaya.
Yuliana, Desi (2007). Pengaruh Variasi Komposisi Serat Serabut Kelapa, Plastik Pet, Serbuk Alumunium Pada Sifat Fisik Dan Koefesien Gesek Bahan Kampas Rem Gesek. Jurusan teknik mesin fakultas teknik universitas muhammadiyah surakarta. Surakarta.
Yuwono,A.H., (2009). Buku Panduan Praktikum Karakterisasi Material 1 Pengujian Merusak (Destructive Testing), Departemen Metalurgi Dan Material Fakultas Teknik Universitas Indonesia, Jakarta.
Refbacks
- There are currently no refbacks.
Copyright (c) 2017 Dinamika Teknik Mesin
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
