RANCANGAN RUANG PENGERING BERBASIS ERGONOMI MENURUNKAN KELUHAN MUSKULOSKELETAL PERAJIN IKAN

I Gede Bawa Susana

Abstract


With  traditional fish drying process,  most possible can cause an unhealthy  working posture , such as a squatting action.   As a consequence , worker will suffer a  musculoskeletal disorders because of not  ergonomic tools and bad working posture. Without ergonomics  working  procedures was found that  the average of   musculoskeletal complaints after working is 52.25 ± 1.03. To solve this ccomplaints, a drying chamber based ergonomics design was built in order to reduce musculoskeletal disorders. Dimensions of the drying chamber were based on anthropometric data of fish craftsmen and the material of drying chamber was by the participatory method. Test was performed on 20 samples and the result showed that the mean rate of  musculoskeletal complaints after working is 38.30 ± 1.30. The ergonomic based design for drying camber application can reduce  the musculoskeletal complaints up to 26.7%.


Full Text:

PDF

References


Adiputra, N., 2004, Ergonomi, Disampaikan dalam Pelatihan Upaya Kesehatan Kerja Tenaga Kesehatan Kabupaten/Kota dan Puskesmas Propinsi Bali, Denpasar, 23-27 Maret dan 29 Maret-2 April.

Bridger, R.S., 2003, Introduction to Ergonomics, 2nd edition, Taylor & Francis, London and New York.

Colton, T., 1985, Statistik Kedokteran, Gadjah Mada University Press, Yogyakarta.

David, G., Wood, V., Li, G., Buckle, P., 2008, The development of the quick exposure check (QEC) for assessing exposure to risk factors work-related musculoskeletal disorders, Journal of Applied Ergonomics, vol. 39, no. 1, 57-69.

Depkes RI., 2003, Survey Indeks Massa Tubuh (IMT) Pengumpulan Status Gizi Orang Dewasa Berdasarkan IMT, Direktorat Bina Gizi Masyarakat.

Goggins, R.W., Spielholz, P., Nothstein, G.L., 2008, Estimating the effectiveness of ergonomics interventions through case studies: implications for predictive cost-benefit analysis. Journal of Safety Research, Elsevier, vol. 39, 339-344.

Kroemer, K.H.E., Grandjean, E., 2000, Fitting the Task to the Human, A Textbook of Occupational Ergonomics, 5th edition, Taylor&Francis, Philadelphia.

Manuaba, A., 1999, Penerapan pendekatan ergonomi partisipasi dalam meningkatkan kinerja industri, Disampaikan dalam Seminar Nasional Ergonomi, Surabaya, 23 Nopember.

OSHA, 2000, Ergonomic: the study of work, Occupational Safety and Health Administration, U.S. Department of Labor.

Pheasant, S., Haslegrave, C.M., 2006, Bodyspace, Antropometry, Ergonomics and the Design of Work, Taylor & Francis London.

Plog, B.A., Quinlan, P.J., 2002, Fundamentals of Industrial Hygiene, Fifth edition, National Safety Council, USA.

Qutubuddin, S.M., Hebbal, S.S., Kumar, A.C.S., 2012, Computer assisted system for enhancing the application of ergonomics in manufacturing systems, International Journal of Ergonomics (IJEG), vol. 2, no. 1, 1-11.

Sanders, M.S., McCormick, E.J., 1993, Human Factors in Engineering and Design, Seventh Edition, McGraw Hill Publishing Company Ltd, New York.

Singh, S., Arora, R., 2010, Ergonomic intervention for preventing musculoskeletal disorders among farm women, J Agri Sci, vol. 1, no. 2, 61-71.

Susila, IG.N., 2002, Gangguan muskuloskeletal, Udayana Medical Journal, vol. 33, no. 120, 90-93.

Tarwaka, 2011, Ergonomi Industri: Dasar-dasar Pengetahuan Ergonomi dan Aplikasi di Tempat Kerja, Harapan Press, Surakarta.

Wignjosoebroto, S., 2011, Ergonomi industri dalam pendidikan terintegrasi: pendekatan ergonomi menjawab problematika industri, Disampaikan dalam Acara Semiloka Linearitas Ergonomi, Fakultas Kedokteran, Universitas Udayana, Denpasar, 21 April.

Wignjosoebroto, S., Partiwi, S.G., Hanafi, A., 2003, Modifikasi rancangan mesin perontok padi dengan pendekatan ergonomi-antropometri, Prosiding Seminar Nasional Ergonomi, Perhimpunan Ergonomi Indonesia (PEI) dan Fakultas Teknologi Pertanian Universitas Gadjah Mada, Yoyakarta, 13 September.

Zheltoukhova, K., O`Dea, L., Bevan, S., 2012, Taking the strain: the impact of musculoskeletal disorders on work and home life, Lancaster University.




DOI: https://doi.org/10.29303/dtm.v6i1.20

Refbacks

  • There are currently no refbacks.


Copyright (c) 2017 Dinamika Teknik Mesin

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

 
After being re-accredited, the Journal of Dinamika Teknik Mesin, still has sinta 3 (S3) which is valid until 2025.
View My Stats