Pengaruh laju pemakanan proses milling terhadap perubahan temperatur pada pahat endmill karbida
Abstract
Cutting Tool temperature has a significant role in the machining process in terms of tool life and workpiece properties. In dry machining process, cutting temperature condition must be monitored as excessive temperature rise can cause tool wear and damage to workpiece. Research on cutting heat has existed along with the development of metal cutting technology. Scientists have made many attempts to determine the cutting heat through theoretical analysis, numerical simulation, and experimental research. Measurement of cutting tool temperature requires a certain method because in milling process the cutting tool rotates to cut the workpiece. This research was condusted with an experimental research using an infrared thermal imager to obtain the result of carbide endmill toll in the face milling process of SKD61 (Special Kogyo Die)steel. The cutting parameters used were 1320 RPM spindle speed, 42, 98, 230 mm/min, and 0.5mm depth of cut. The milling process carried out with a time frequency of 5 minutes. The results of carbide endmill tool temperature measurement show that increasing the feed rate affects the temperature rise of the carbide endmill tool. At the feed rate of 42 mm/min, the highest temperature recorded was 152.3 ˚C, then at the feed rate of 98 mm/min, the highest temperature was 195 ˚C, and the feed rate of 230 mm/min had the highest temperature in this study, which was 219.4 ˚C.
Keywords
Full Text:
PDFReferences
Bahry, N. A., Nurrohkayati, A. S., Analisis perubahan temperatur mata pahat karbida pada proses pembubutan baja aisi 1045 dengan fem-simulation di pt. x, TEKNOSAINS: Jurnal Sains, Teknologi dan Informatika, 9(2), 65–73, 2022.
Habrat, W., Krupa, K.,Markopoulos, A. P., Karkalos, N. E., Thermo-mechanical aspects of cutting forces and tool wear in the laser-assisted turning of Ti-6Al-4V titanium alloy using AlTiN coated cutting tools, International Journal of Advanced Manufacturing Technology, 115(3), 759–775, 2021.
Jiang, F., Liu, Z., Wan, Y., Shi, Z., and Zhang, H., Experimental investigation of cutting tool temperature during slot milling of AerMet 100 steel, Proc Inst Mech Eng B J Eng Manuf, 230(5), 838–847,2016.
Laperriere, L., Reinhart, G., Encyclopedia of production engineering, CIRP-The International Academy for Production Engineering, 2014.
Liao, Z.,Schoop J., Saelzer J., Bergmann B., Priarone P., Splettstößer A., Bedekar V., Zanger F., Kaynak Y., Review of current best-practices in machinability evaluation and understanding for improving machining performance, CIRP J Manuf Sci Technol, 50, 151–184, 2024.
Liu, Y., Cui, N., Chen, H., Effect of temperature on milling stability of thin-walled parts, Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture, 2022.
Lubis, S. Y., Reynaldi, Askolani, A. P., Ariyanti, S., J. Teknologi Industri, and P. Teknik Mesin, Analisis keausan mata pahat dan waktu pemotongan pada proses drilling baja S 45 C, Prosiding SERINA III, 2021.
Lubis, S. M., Darmawan, S., Adianto, Ericsen, Effect of cutting speed on temperature cutting tools and surface roughness of AISI 4340 steel, IOP Conf. Series: Materials Science and Engineering 508, 2019.
Nasution A. R., Rahmatullah, R., Harahap, J., Pengaruh variasi putaran spindel terhadap gaya potong pada proses pemesinan, VOCATECH: Vocational Education and Technology Journal, 2(2),92–99, 2021.
Ogedengbe, T.S., Okediji, A. P., Yussouf, A. A., Aderoba, O. A., Abiola, O. A., Alabi, I. O., Alonge, O. I., The effects of heat generation on cutting tool and machined workpiece, in Journal of Physics: Conference Series, Institute of Physics Publishing, 2019.
Rochim, T., Teori dan Teknologi Proses Pemesinan. Penerbit HEDS, Bandung, 1993.
Susanto, A. ., Yuwono, I., Wahyudi, N., Wicaknono, R., Analisa gaya potong pada proses frais komponen kereta api menggunakan octave: bagian 1 up milling, Manutech : Jurnal Teknologi Manufaktur, 13(02), 60 – 67, 2021.
Sifa, A., Endramawan, T., Putra, M. P., Suwandi, D., and Amat, M. A., Utilization of minimum quantity lubrication (mql) chip fan on ss304 during milling process to increase carbide tool life, International Journal of Automotive and Mechanical Engineering, 19(4), 10073–10083, 2022.
Thành N.T., An, N.T., Simulation-based optimization for preform’s dimensions of an automotive bevel gear, Conference: Proceeding of the 5th National Conference on Mechanical Science & Technology, 2018.
Yang, X., Chen, P., Heat transfer enhancement strategies for eco-friendly dry hobbing considering the heat exchange capacity of chips, Case Studies in Thermal Engineering, 29, 2022.
Zgórniak, P., Stachurski, W., and Ostrowski, D., Application of thermographic measurements for the determination of the impact of selected cutting parameters on the temperature in the workpiece during milling process, Strojniski Vestnik/Journal of Mechanical Engineering, 62(11), 657–664, 2016.
Zhou, R., Analytical model of workpiece surface temperature prediction in 4-axis milling process, International Journal of Advanced Manufacturing Technology, 111(8), 2155–2162, 2020.
DOI: https://doi.org/10.29303/dtm.v14i2.881
Refbacks
- There are currently no refbacks.
Copyright (c) 2024
![Creative Commons License](http://licensebuttons.net/l/by-nc/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
![](/public/site/images/admin/Sertifikat_DTM_20241.png)